3D Printers

Set Up Guides | Tech. Specs. | Unboxing | Tips | Common Issues | FlashForge | UP!

Jon Soong avatar Lap avatar Roland Peddie avatar +2
39 articles in this collection
Written by Jon Soong, Lap, Roland Peddie and 2 others
General Issues

How do I adjust nozzle offset to compensate for errors in auto calibration?

How to adjust the nozzle offset of your printer to compensate for an error in auto calibration.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I set the height of a manual nozzle?

If your auto calibration doesn't work, or the available Nozzle Offset isn't enough to fix it, try Manually Calibrating the Nozzle
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

Help! The extruder isn't heating up. What should I do?

If your printer doesn't seem to be heating up when you click print, follow these instructions
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

What do I do if my printer says it's out of material?

Here is how to reset your printers on-board filament measurement.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

Why isn't the text on a design being printed?

Learn about why some small text can't be physically 3D printed
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I fix the nuts falling off when the bed is levelling?

This will correct levelling, if the nuts gets to the end of the bolt, and falls off before touching the sensor.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I remove Hotend Assembly?

How to remove your entire Hotend Assembly
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How can I fix a blocked nozzle? (For advanced/experienced users only.)

Please only use this guide if it's been recommended to you by Makers Empire
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago
Flashforge Inventor IIS 3D Printer | Bilby 3D Printers

What are the tech specs for the Flashforge Inventor IIs 3D printer?

Tech specs for the Flashforge Inventor IIs 3D printer
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How does the Inventor IIS work?

The process of 3D printing from Makers Empire
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I unbox and setup the Inventor IIs?

This article will walk you through the process of unboxing and setting up your Inventor IIS, ready for printing.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I connect my Inventor IIs to my wifi network?

Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I print with the FlashForge Inventor IIs via ethernet?

Use ethernet / network cable instead of WiFi
Jon Soong avatar
Written by Jon Soong
Updated over a week ago

How do I install the FlashPrint software for the Inventor IIS and Guider IIS?

To control your Inventor IIS or Guider IIS, follow these instructions on how to install the software on your computer or laptop.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I load filament into the Inventor IIs 3D Printer?

This article will show you, step-by-step, how to load filament into the Inventor IIS
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I remove filament from the Inventor IIS?

This article walks you through the process of removing filament, and storing it.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I send my first print to a FlashForge?

This article will help you through the process of setting up the Flashprint software, and sending your first print.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I calibrate the extruder on the Flashforge Inventor IIS?

This adjusts the distance between the nozzle and the print bed
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I preheat the Inventor IIs?

Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I level the bed on the Inventor IIS?

This article will walk you through the process of levelling the print bed on the Inventor IIS.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I remove the print from an Inventor IIs?

This article explains the process of removing a print from the Inventor IIS
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How do I clear a clog in the Inventor IIs?

Steps to clear a blockage inside the extruder of the Inventor IIS
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

Help! The nozzle of my Inventor IIs is digging into the print bed and nothing is coming out. What should I do?

This article will help you calibrate the extruder on your Inventor IIS
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

Why aren't prints sticking to the print bed of my FlashForge Inventor IIs?

This article will help you calibrate the extruder on your Inventor IIS
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

Does the Inventor IIS store previous prints?

Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago

How To Connect Your Flashforge Inventor IIS To The Polar Cloud And 3D Print Your Designs

Learn how to print via the Polar Cloud using your Flashforge Inventor IIS 3D printer
Jeanette McConnell avatar
Written by Jeanette McConnell
Updated over a week ago

How do I unbox and setup an Inventor IIs - Bilby3D?

This article will walk you through the process of unboxing and setting up your Inventor IIS - Bilby3D, ready for printing.
Luke Tansell avatar
Written by Luke Tansell
Updated over a week ago